Test
Very strong and rugged clear polycarbonate box to store standard pin mounts with 3.2mm (1/8"). This box is watertight, crushproof and dustproof. The strong hinges, locking clasps and soft silicone O-ring seal makes this an ideal transport, shipping and storage box for SEM samples on pin mounts. The holder insert is numbered 1-18 and accommodates all types of pin mounts form 6.4 to 50mm diameter.
For the storage of 15 capsule blocks in numbered cavities.
Accommodates up to 31.8 mm (1.25") diameter of a metallurgical specimen with at least 0.8 mm (1/8") clearance, pin is 3.1 mm (1/8"), depth is 8 mm (5/16")
Scanning electron microscope specimen mount with 45 degree angle. Made from lathe finished ultra-pure aluminum.
Head: 5/8"
Height: 3/8"
This mount which is made from aluminum is used for the mounting and tilting of samples from 0 – 90 degrees as well as for SEM investigation with small working distances. The mount is marked for 30, 45, 70 and 90 degress. The table measures 11 x 11 mm (0.46" x0.46")and the overall size is 14 x 14 x12.7 mm
Type: Hitachi M4
Luer stub / blunt needle, 15ga x 0.5in (12mm). Amber. 50 sterile pouches of 5.
Machined from solid steel and brass/nickel plated. Incorporates a stainless steel mesh top and bottom to allow for fluid exchange. Comes with two sections; each section holds 12 specimens in 12 cavities cavity measures 4.5mm(D) x 6mm(H)..
Lanthanum hexaboride (LaB6) and cerium hexaboride (CeB6) cathodes are ideal for many small spot size applications such as SEM, TEM, surface analysis and metrology, and for high current applications such as microwave tubes, lithography, electron-beam welders, X-ray sources and free electron lasers. Greater brightness from low work function yielding higher currents at lower temps than tungsten. Cambridge SMVM base.
Type: CEBIX (CeB6)
Angle: 90°
Tips: 20 mm
Machined from solid steel and brass/nickel plated. Incorporates a stainless steel mesh top and bottom to allow for fluid exchange. Comes with two sections; each section holds 6 specimens in 6 cavities cavity measures 7.5mm (D)x6mm(H)..
The QX-102 Capsules are used for scanning electron microscope imaging of wet materials and biological samples, including liquid foods, cosmetics, oils, and paints, particles in solutions, adherent and non-adherent human and animal cells, and microorganisms. The samples can be visualized either directly or by following appropriate contrast enhancement staining or labeling procedures. The capsule serves as a cell culture dish, specifically designed for the SEM . No coating or embedding of the sample are required, enabling electron microscopy imaging with easy sample preparation comparable to light microscopy.
The QX-302 Calibration Capsule is a QX-302 Capsule designed to assist first time users in finding optimal imaging conditions for WETSEM imaging in their SEM .
Circlips are for all EMS TEM sample holders and specimen rods. They are made from heat treated Beryllium copper. The Circlip extraction tool is for removing our Circlips from all TEM sample holders.
Cambridge, Phillips, Camscan, B&L, Etec, Zeiss SEM specimen mounts. Tapered end pin, slotted head.
Head: 1/2"
Pin height: 6 mm
Pin diameter: 1/8"
Cambridge, Phillips, Camscan, B&L, Etec, Zeiss SEM specimen mounts. Tapered end pin, slotted head.
Head: 1/2"
Pin height: 6 mm
Pin diameter: 1/8"
Aluminum Mini SEM clamp on a 10 mm, 15 mm diameter M4 cylinder mount. Convenient for holding flat or thin specimens such as silicon chips, wires, foil and small tubes. Screw is M2 x 3 mm, pan head screw, brass.