Test
Very strong and rugged clear polycarbonate box to store standard pin mounts with 3.2mm (1/8"). This box is watertight, crushproof and dustproof. The strong hinges, locking clasps and soft silicone O-ring seal makes this an ideal transport, shipping and storage box for SEM samples on pin mounts. The holder insert is numbered 1-18 and accommodates all types of pin mounts form 6.4 to 50mm diameter.
For the storage of 15 capsule blocks in numbered cavities.
Machined from solid steel and brass/nickel plated. Incorporates a stainless steel mesh top and bottom to allow for fluid exchange. Comes with two sections; each section holds 12 specimens in 12 cavities cavity measures 4.5mm(D) x 6mm(H)..
The QX-102 Capsules are used for scanning electron microscope imaging of wet materials and biological samples, including liquid foods, cosmetics, oils, and paints, particles in solutions, adherent and non-adherent human and animal cells, and microorganisms. The samples can be visualized either directly or by following appropriate contrast enhancement staining or labeling procedures. The capsule serves as a cell culture dish, specifically designed for the SEM . No coating or embedding of the sample are required, enabling electron microscopy imaging with easy sample preparation comparable to light microscopy. Includes QX-202 Capsules and all the accessories.
Specially designed for easy, quick and clean mounting of any type of thin specimen on specimen stubs. These spring-loaded clips accommodate samples of up to 2 mm thickness. Samples are held securely by small spring-loaded clips and allow for easy change of samples. Adhesives are not required, eliminating possible outgassing issues and saving time. Ideal for holding silicon chips, paper, wire, threads, thin films, sheet metal, etc.
Diameter: 25 mm
Includes: 3 clips
These spring-loaded clips accommodate samples of up to 2 mm thickness. Samples are held securely by small spring-loaded clips and allow for easy change of samples. Adhesives are not required, eliminating possible outgassing issues and saving time. Available with single and multiple clips and are ideal for holding silicon chips, paper, wire, threads, thin films, sheet metal and more. SEM Clip Mounts with multiple clips can hold larger samples or multiple smaller samples.
Includes: 8 clips
Diameter: 50 mm
Pin height: 6 mm
SEM specimen holder with two 1 mm by 3 mm deep slots. Clamp thin specimens and cross sections without conductive paint or tape. 3.2 mm pin. Machined aluminum with 2 stainless steel allen set screws. Includes allen wrench.
Specially designed for easy, quick and clean mounting of any type of thin specimen on specimen stubs. These spring-loaded clips accommodate samples of up to 2 mm thickness. Samples are held securely by small spring-loaded clips and allow for easy change of samples. Adhesives are not required, eliminating possible outgassing issues and saving time. Ideal for holding silicon chips, paper, wire, threads, thin films, sheet metal, etc.
Diameter: 38 mm
Includes: 2 clips
These spring-loaded clips accommodate samples of up to 2 mm thickness. Samples are held securely by small spring-loaded clips and allow for easy change of samples. Adhesives are not required, eliminating possible outgassing issues and saving time. Available with single and multiple clips and are ideal for holding silicon chips, paper, wire, threads, thin films, sheet metal and more. SEM Clip Mounts with multiple clips can hold larger samples or multiple smaller samples.
Includes: 1 clip
Diameter: 50 mm
Pin height: 6 mm
Mini SEM pin stub mount for Cambridge, Leica, ZEISS/LEO, FEI/Philips, CamScan, Tescan, ETEC and Amray. Made from lathe finished ultra-pure aluminum.
Head: 6.6 x 1.3 mm
Pin height: 3/8"
Cylinder specimen mounts are for use with JEOL scanning electron microscopes. The mounts are made from ultra-pure aluminum with a standard lathe finish.
Head: 1-1/4"
Height: 3/8"
The fixation clips 6 mm in diameter provide support spring for small and thin specimens during mounting.
Circlips are for all EMS TEM sample holders and specimen rods. They are made from heat treated Beryllium copper. The Circlip extraction tool is for removing our Circlips from all TEM sample holders.
Cambridge, Phillips, Camscan, B&L, Etec, Zeiss SEM specimen mounts. Tapered end pin, slotted head.
Head: 1/2"
Pin height: 6 mm
Pin diameter: 1/8"
Specially designed for easy, quick and clean mounting of any type of thin specimen on specimen stubs. These spring-loaded clips accommodate samples of up to 2 mm thickness. Samples are held securely by small spring-loaded clips and allow for easy change of samples. Adhesives are not required, eliminating possible outgassing issues and saving time. Ideal for holding silicon chips, paper, wire, threads, thin films, sheet metal, etc.
Diameter: 38 mm
Includes: 2 clips